ZCLS Pneumatic thin film angle high-pressure regulating valveDetailed product description：

Characteristics of ZCLS Pneumatic Thin Film Angle High Pressure Regulating Valve

German technology has a long lifespan and a single seat valve core with medium pressure and high pressure. The angular structure of the anti blocking and anti sticking film mechanism is easy to use

Overview
Pneumatic thin film room temperature and medium temperature angle single seat valve, with a right angled valve body and a single guide valve core structure. The valve has a simple flow path, making it easy to clean and clean. Low resistance, suitable for regulating high viscosity fluids containing suspended and granular substances, can avoid coking, adhesion, and blockage.

Main technical parameters of ZCLS pneumatic thin film angle high-pressure regulating valve regulating mechanism

Nominal diameter mm	twenty	twenty-five	thirty-two	forty	fifty	sixty-five	eighty	one hundred	one hundred and twenty-five	one hundred and fifty	two hundred
Valve seat diameter mm	10. 12, 15, 20	twenty-six	thirty-two	forty	fifty	sixty-five	eighty	one hundred	one hundred and twenty-five	one hundred and fifty	two hundred
Rated flow coefficient kv	1.6，2.5，4.0，6.3	ten	sixteen	twenty-five	forty	sixty-three	one hundred	one hundred and sixty	two hundred and fifty	four hundred	six hundred and thirty
Nominal pressure MPa	0.6 4.0 6.4
Travel distance mm	ten	sixteen		twenty-five		forty			sixty
flow characteristics	Straight line equal percentage
Medium temperature ℃	-20-200, -40 to+250 (normal temperature type) -40 to 315 (medium temperature type)
Flange size	Cast iron flange size according to JB79-59, cast steel flange size according to JB79-59
Flange type	According to JB77-59, the cast steel flange is smooth and the cast steel flange is concave
Valve body material	HT200,ZG230-450、ZG1Cr18Ni9Ti、ZG0Cr18Ni12Mo2Ti
Upper valve cover type	Ordinary type (constant temperature type), hot plate type (medium temperature type)
Adjustable ratio	30:1

Main technical parameters of the executing agency

Model number	ZHA(B)-2	ZHA(B)-3	ZHA(B)-4	ZHA(B)-5
Effective area cm2	two hundred and eighty	four hundred	six hundred and thirty	one thousand
Travel distance mm	10,16	twenty-five
Spring range KPa	20～100； 40-200, 20-60, 60-100, 80-240

Main technical performance indicators

project	Without locator	Equipped with locator
Basic error%	±5	±1.0
Return difference%	three	one
Dead zone%	three	zero point four
Rated travel deviation% (gas shut-off)	two point five
Allowable leakage rate L/h	1 × 10-4 × rated capacity of valve

Allowable pressure difference

Nominal diameter mm

twenty

twenty-five

thirty-two

forty

fifty

sixty-five

eighty

one hundred

one hundred and twenty-five

one hundred and fifty

two hundred

Valve seat diameter mm

ten

twelve

fifteen

twenty

twenty-six

thirty-two

forty

fifty

sixty-six

eighty

one hundred

one hundred and twenty-five

one hundred and fifty

two hundred

Effective area of film cm2

two hundred and eighty

four hundred

six hundred and thirty

one thousand

Maximum allowable pressure difference (MPa)

five point three five

three point seven

three point four

one point three five

zero point eight

zero point five five

zero point five

zero point three

zero point three

zero point two

zero point one two

zero point one two

zero point zero eight

zero point zero five

Note: When the maximum allowable pressure difference is P2=0, the signal of the pneumatic actuator is 10KPa, and the signal of the pneumatic actuator is 0.
Can be equipped with accessories
Positioner, pressure gauge, handwheel, solenoid valve, limit switch, electric/pneumatic converter, air filter, pressure reducer

Main component materials and recommended temperature range for use

Part Name	material	temperature range
Valve body Upper and lower valve covers	HT200	-20～200℃
	ZG230-450	-40～450℃
	ZG1Cr18Ni9Ti	-250～550℃
Valve core, valve seat, valve stem	1Cr18Ni9	-250～550℃
Upper and lower membrane covers	A3 steel plate
Bracket, top plate	HT200
compression spring	60Si2Mn
Wave spun film	5806 rubber clip 480D nylon 66 mesh fabric
filler	Polytetrafluoroethylene	-40～200℃
	carbon fiber	-120～350℃
gasket	asbestos rubber sheet
	1Cr18Ni9 asbestos board
Bolt, double headed bolt	35, 25
	35CrMoA
	35CrMoA
nut	A3
	25, 35

Dimensions of ZCLS Pneumatic Thin Film Angle High Pressure Regulating Valve

Nominal Diameter DN	line Cheng	L			H				D
		PN MPa			Room temperature type		Medium temperature type
		one point six	four	six point four	Air opening type	Airtight type	Air opening type	Airtight type
twenty	ten	eighty-five	eighty-five	one hundred	five hundred and seventy-four	five hundred and thirty-seven	seven hundred and twenty-five	six hundred and eighty-eight	two hundred and eighty
twenty-five	sixteen	ninety-five	ninety-five	one hundred and fifteen	five hundred and eighty-nine	five hundred and fifty-two	seven hundred and thirty-eight	seven hundred and one	two hundred and eighty
thirty-two	sixteen	one hundred and fifteen	one hundred and fifteen	one hundred and thirty	five hundred and eighty-nine	five hundred and fifty-two	seven hundred and thirty-eight	seven hundred and one	two hundred and eighty
forty	twenty-five	one hundred and fifteen	one hundred and fifteen	one hundred and thirty	six hundred and fifty-four	six hundred and two	eight hundred and three	seven hundred and fifty-one	three hundred and fifty-two
fifty	twenty-five	one hundred and thirty	one hundred and thirty	one hundred and fifty	six hundred and fifty-nine	six hundred and seven	eight hundred and eight	seven hundred and fifty-six	three hundred and fifty-two
sixty-five	forty	one hundred and forty-five	one hundred and forty-five	one hundred and seventy	nine hundred and forty-two	eight hundred and fifty-six	one thousand one hundred and twenty-three	one thousand and thirty-seven	four hundred and ten
eighty	forty	one hundred and fifty-five	one hundred and fifty-five	one hundred and ninety	nine hundred and twenty-eight	eight hundred and forty-two	one thousand one hundred and nine	one thousand and twenty-three	four hundred and ten
one hundred	forty	175,	one hundred and seventy-five	two hundred and fifteen	nine hundred and twenty-eight	eight hundred and forty-two	one thousand one hundred and nine	one thousand and twenty-three	four hundred and ten
one hundred and twenty-five	sixty	two hundred	two hundred	two hundred and fifty	one thousand one hundred and twenty-two	one thousand and ten	one thousand three hundred and thirty-five	one thousand two hundred and twenty-three	four hundred and ninety-five
one hundred and fifty	sixty	two hundred and forty	two hundred and forty	two hundred and seventy-five	one thousand one hundred and twenty-four	one thousand and twelve	one thousand three hundred and thirty-two	one thousand two hundred and twenty	four hundred and ninety-five
two hundred	sixty	three hundred	three hundred	three hundred and twenty-five	one thousand one hundred and forty-nine	one thousand and thirty-seven	one thousand three hundred and sixty-two	one thousand two hundred and fifty	four hundred and ninety-five

Ordering Instructions
1. Product model and name 2. nominal diameter DN (mm)
3. Nominal pressure 4. Flow characteristics
5. Valve body material and sealing requirements 6. Rated flow coefficient
7. Type of medium and temperature range 8. Pressure difference before and after the valve
9. Gas source pressure and control method 10. Other special requirements